On the basis of design documentation for the device should be corrosion resistant coatings to develop the project of works (CPD) in accordance with the requirements of SNIP 01/03/01, of which should include flow sheets device to separate anti-corrosion coatings. In the process maps on the device coatings should provide the following basic requirements: – the preparation of materials – "the preparation of the surface structure under the protective covering – "Application of primer or primer-impregnation -" a protective coating in one or more layers – "keeping the coating on the air until it hardened, drying or heat treatment; – "Okislovke surface. Materials used for corrosion resistant coatings device must comply with the requirements of existing TNLA. Their quality must be confirmed by quality certificate of the manufacturer and in accordance with applicable law, – the certificate of conformity of the National System of conformity or technical evidence. Transportation, warehousing and storage of materials, as well as structures and equipment coated with a protective coating on the construction site should be in accordance with the requirements of TNLA for this product (product). Quality Control Devices anticorrosive coverings should be in accordance with the requirements of existing TNLA. The ambient air temperature, shielding materials and surfaces to be protected must not be below 10 C – for paint coatings, prepared on the basis of natural resins, mastic and coatings shpatlevochnyh of silicate materials okleechnoy protective coatings on the basis of bitumen roll materials, poliizobutilenovyh plates, duplicate polyethylene gummirovochnyh coatings facing and lining coatings arranged on kislotoupor-GOVERNMENTAL silicate plaster, on the mastic bituminol; for acid-concrete and concrete-silikatopolimer; surface impregnation, 15 C – to paint the reinforced and unreinforced coatings and liquid covering a bearing of the materials prepared by synthetic resins, mastic coatings and sealants Nairit prepared on the basis of synthetic rubbers; coating of sheet polymeric materials lining and lining coatings, carried out on plaster arzamit, furaktor, polyester, epoxy resins for polymer concrete, cement and polystyrene, cement and cement-perchlorovinyl casein plasters.
25 C – for latex coatings (such as "sex"). Work to protect building structures against corrosion should be done after all prior to construction works, the production process where the protective coating can be damaged. When the negative air temperature corrosion work should be carried out in heated rooms or shelters, if the project documentation is not provided the possibility of the device of the coating at low air temperatures. At negative temperatures may only restoration of damaged anticorrosion coatings (except for the use of sacrificial metal plasters). Relative humidity in the production of anti-corrosion work should be not higher than 70%. The metal surface prepared for the production of anti-corrosion work, should not have burrs, sharp edges, weld spatter, rolls, burn-through, flux residues, slag, oxides formed during welding, defects produced during the rolling and casting in the form of non-metallic makrovklyucheny, sinks, cracks, delamination, uneven, and the fat-pounds of pollution, rust and old paint. The most thoroughly be cleaned surface in the zone of welds up to 3 cm of flux residues, slag and alkali oxides formed during welding
Are ergometers already trained more than just simple fitness equipment today? On the home market of sports, there is now a colorful variety of different devices. A few years ago, it was hardly conceivable that you can order these devices online. Now, there are actually a whole bunch of different online stores, which make it easy for the consumer to make an active and meaningful training. Try it yourself easily! With the bike on the coaster did you know, that same technology is being used as in classic launch coasters in ergometers? Same technology is used in theme parks, as well as on the Ergometer. Eddy current brakes should provide a powerful acceleration on the roller coaster, at ergometers, however, the resistance is adjusted using this technology. The resistance can be set at most training devices with the help of the onboard computer. There is no place more clarified so for retailers in no other industry in recent years is the Internet on the rise. While in the 1990s more than half have ordered their trainers in specialized or supermarkets of all customers, the statistics goes in the last 10 years in a completely different direction.
Meanwhile, more than 70% of all training equipment on the Internet are sold. No wonder, because customers have to inform many more on various pages about current test reports. The guilty conscience while the sales figures of many sectors weakened in early January, really start it so after the holidays have season. No wonder, because the bad conscience reports after new year’s Eve and new year’s to word quickly and loudly. At Christmas time you could justify the extra kilos, after the new year but for most people: urgent remedy. Therefore it is not surprising that sales of fitness equipment manufacturers go heavily back in the summer and rising significantly in the winter. Not only quality and service as there are many people who do not quite trust online shopping To want.
Therefore, the service many people plays a major role and should not be taken therefore also lightly. Many manufacturers are striving to improve quality and regularly ask their customers for feedback. The interesting thing here: The positive reviews concern mainly the service and the speed. The device itself is rarely mentioned in the feedback. An increase to the exercise bike many buyers don’t know the difference between a bike and an exercise bike Ergometer. The difference can be crucial. An Ergometer, for example, has significantly more functionality than a simple exercise. Also the resistance setting and the pulse the equipment is much more extensive and complex.
This monograph showed study on the use of technology RFID; technology that uses the radio waves automatically to identify people, animals and objects; applied in the management of the warehouse of a multinational company, located in the city of Matozinhos, MG. Its objective is to evaluate the effectiveness of technology RFID, through a simulation, in the attendance to the particularitities of the control of the processes that involve the identification of asset in this warehouse, where the intelligent labels supplied by technology RFID must inform to the control system its parameters, what it makes possible the automatic identification of asset. So that the considered objective was reached was made bibliographical study, in order to get knowledge on the main characteristics that involve the technology, beyond analysis of the logistic one of the warehouse sector, through the study of the current processes, analysis of viability in search of vulnerabilities and to know the existing tools in the market for creation of the simulator environment. The software tools had been described proposals for the Rifidi for simulator environment implantation, being carried through comparative between them on the basis of the parameters defined in the sections of analyses, for choice of the adequate solution. After defined the tool, a study of case based on the implantation of software in a computer, being carried through the configuration and execution of this software was made. The results had allowed to evaluate the effectiveness of the process of automatic identification of asset in movement in the controlled environment, being also applied in the comparative degree with the results of the processes used currently..